Article ID : 00112938 / Last Modified : 09/27/2018

Non-Android TV stuck in reboot loop and ON/OFF power LED blinks 8 times (2012 Models)

    You may be experiencing a rebooting loop on your TV - illustrated by the ON/OFF power LED blinking 8 times. This is affecting only 2012 Internet Internet TVs.

    Some customers have reported the below instruction to potentially bring the situation back to normal.

    Check this page regularly for updates.

    Depending on how your TV is connected to the Internet, please use one of the following recovery methods:


    Wired Ethernet LAN connections

    1. Unplug the TV power cord from the electrical outlet
    2. Disconnect your Ethernet cable from the TV
    3. Plug the power cord back in to the electrical outlet
    4. Turn on your TV
    5. Perform a factory reset:
      • Press and hold the up arrow button on the remote control.
      • While holding the up arrow button, press and release the Power on button on the side of the TV.
        Reset will appear momentarily on the lower left hand corner of the TV
      • Release the up arrow button on the remote control and wait for the TV to reset
    6. After the Reset message appears, allow the TV to reset. Do not press any buttons on the remote control or on the TV and do not make any other adjustments for 1 minute.
    7. Upon completion, unplug the power cord from the electrical outlet
    8. Allow the TV to remain without power for 10 seconds
    9. Reconnect your Ethernet cable to the TV
    10. Plug the power cord back in to the electrical outlet
    11. Turn on the TV.

      NOTE: The initial setup screen displays if the above procedures were performed correctly
    12. Follow the on-screen instructions to complete the initial set up

      IMPORTANT: If the reset did not complete successfully, disconnect all devices from the TV, and then repeat the procedure from step 1.

    Built-in Wireless LAN connections

    1. Unplug the TV power cord from the electrical outlet
    2. Turn off your Wi-Fi router
    3. Plug the power cord back in to the electrical outlet
    4. Turn on your TV
    5. Perform a factory reset:
      • Press and hold the up arrow button on the remote control.
      • While holding the up arrow button, press and release the Power on button on the side of the TV.
        Reset will appear momentarily on the lower left hand corner of the TV
      • Release the up arrow button on the remote control and wait for the TV to reset
    6. After the Reset message appears, allow the TV to reset. Do not press any buttons on the remote control or on the TV and do not make any other adjustments for 1 minute.
    7. Upon completion, unplug the power cord from the electrical outlet
    8. Allow the TV to remain without power for 10 seconds
    9. Turn on your Wi-Fi router
    10. Plug the power cord back in to the electrical outlet
    11. Turn on the TV.

      NOTE: The initial setup screen displays if the above procedures were performed correctly
    12. Follow the on-screen instructions to complete the initial set up

      IMPORTANT: If the reset did not complete successfully, disconnect all devices from the TV, and then repeat the procedure from step 1.

    USB Dongle Wireless LAN connections

    1. Unplug the TV power cord from the electrical outlet
    2. Disconnect your USB dongle from the TV
    3. Plug the power cord back in to the electrical outlet
    4. Turn on your TV
    5. Perform a factory reset:
      • Press and hold the up arrow button on the remote control.
      • While holding the up arrow button, press and release the Power on button on the side of the TV.
        Reset will appear momentarily on the lower left hand corner of the TV
      • Release the up arrow button on the remote control and wait for the TV to reset
    6. After the Reset message appears, allow the TV to reset. Do not press any buttons on the remote control or on the TV and do not make any other adjustments for 1 minute.
    7. Upon completion, unplug the power cord from the electrical outlet
    8. Allow the TV to remain without power for 10 seconds
    9. Reconnect your USB dongle to the TV
    10. Plug the power cord back in to the electrical outlet
    11. Turn on the TV.

      NOTE: The initial setup screen displays if the above procedures were performed correctly
    12. Follow the on-screen instructions to complete the initial set up

      IMPORTANT: If the reset did not complete successfully, disconnect all devices from the TV, and then repeat the procedure from step 1.

    This information is only applicable for the following 2012 models:
     

    KDL-22EX550

    KDL-22EX553

    KDL-22EX555

    KDL-26EX550

    KDL-26EX553

    KDL-26EX555

    KDL-32EX650

    KDL-32EX653

    KDL-32EX655

    KDL-32HX750

    KDL-32HX751

    KDL-32HX753

    KDL-32HX755

    KDL-32HX757

    KDL-32HX758

    KDL-32HX759

    KDL-40EX650

    KDL-40EX653

    KDL-40EX655

    KDL-40HX750

    KDL-40HX751

    KDL-40HX753

    KDL-40HX755

    KDL-40HX756

    KDL-40HX757

    KDL-40HX758

    KDL-40HX759

    KDL-40HX75G

    KDL-40HX850

    KDL-40HX853

    KDL-40HX855

    KDL-46EX650

    KDL-46EX653

    KDL-46EX655

    KDL-46HX750

    KDL-46HX751

    KDL-46HX753

    KDL-46HX755

    KDL-46HX756

    KDL-46HX757

    KDL-46HX758

    KDL-46HX759

    KDL-46HX75G

    KDL-46HX850

    KDL-46HX853

    KDL-46HX855

    KDL-55HX750

    KDL-55HX751

    KDL-55HX753

    KDL-55HX755

    KDL-55HX75G

    KDL-55HX850

    KDL-55HX853

    KDL-55HX855

    KDL-55HX950

    KDL-55HX953

    KDL-55HX955

    KDL-65HX950

    KDL-65HX953

    KDL-65HX955

    KD-84X9005